I'm not really all that artistic like most of the people here, but I figured I'd share this for the other gun guys.
So, sometimes I get a little free time at work in the shop, which is nice. Recently, I've begun playing around with a Ruger SR1911 I've had kicking around for a couple years. I've built and rebuilt a few 1911s, but never done much in depth stuff, just swapping bits here and there.
This one, I've decided to go full out on. It started off looking kinda like this:

First step was to yank the slide release. It got replaced with a forged Norinco - they aren't great, but are HUGE. I have small hands and am left-handed, and this is the only thing big enough that I can consistently hit it with my index finger. Next, the mag release was taken down a bit, and recheckered. Looks like the factory, but is just a bit shorter so I don't accidentally hit that one. Then the safety. Some decent Wilson Combat ambis go in - low profile since I've never really used safeties, as you can't pack a gun around here.
Factory Novaks were yanked and replaced with Tru-Glo stuff, thrice actually. Funny story, I was busy doing other shit and had someone else here put in the first two pairs. They both fell out within about 25 rounds. Somewhere out in the dirt, there's $600 worth of glow in the dark gun sights. Third time, I did it myself, and they're still there, thankfully. For the record, tritium sights are kind of a waste of money even when they don't fall out - I've got a 12 ga for home defense if the 80 year old woman next door decides to try to murder me, and besides whipping around the house with this thing and having the glows make me feel all badass, they are kinda pointless.
Grips were originally swapped with some Pachmayer American Legends with a wrap, which got lost in the shop somewhere when I did the next step. So, it's got grippers for now, which are likely gonna get chucked in favor of some VZ grips.
And re-profiling will need to happen. I was digging around in a bin upstairs, and stumbled on a jig for bobtailing 1911s. This is badass, as my little hands don't fit the standard GOVT sized guns as well as most of my other pistols. So into the chopping block it went. Considering I'd never done one before, it turned out ok. I used an Ed Brown mainspring housing that just happened to be around - it's pretty super aggressive, which is good.
Finally, a bit of trigger tweaking, a little polishing here and there, and this is what I've got now:



And one with the grippers on it, cause why not. As I said, I didn't bother to profile them since I can't find my scissors and plan on swapping them in the next week or two for something nicer.
For some reason, TinyPic insists that this is the picture I uploaded.
So here's a direct link to that one instead. Which doesn't work either. I don't know. Picture that with rubber finger groove grips on it.
Still to do:
1. Replace those grips. I'm thinking some
VZ Operators in tiger stripe, or maybe some
Wilsons.
2. Laser engraving. I'm kinda undecided on it, but I have this handy laser engraver here. I'm thinking either grip medallion inserts, or where the ruger logo is now - might put
this there, so that it will match my discordian themed tattoos. I might not, too. Depends what color it ends up being. Medallions would likely go best with the "theme" here, but I'm not sure if I'll find time to make them.
3. Cerakoting. I've gotten everything all tightened up, which was a mistake, as I'd still like to cerakote at least part of it. I'm thinking a nice, simple, two tone flat black with the slide, kind of like
this. Those are the same type grips that were originally on it, and might end up going back on it if I skip step 1 and can find them.
4. Cerakote the magazine baseplates. I've got a color scheme I've used forever for the one handgun that I do leave at home for my wife, so that she knows which ones have bullets that will go through the wall and kill the kids, and which ones are frangible, should she ever decide to lose it and shoot the house up. Black for FMJ, gold for HP, and blue for frangibles. I have a million 1911 mags around and don't usually leave this one at home, so I might not bother with this.
5. Replace the grip screws with
these. Cause why the fuck not.
After this project is done, it's on to learning how to sew and making a holster for this motherfucker:

And if you fellas insist on some "art", here's a drawing I did of some customer who kept me on the phone for an hour and a half. I was running out of shit to scribble well before the call was over.